White Rabbit
02-06-2003, 01:28 AM
Warning: The following is for educational purposes only, any attempt to recreate the outlined procedure could result in severe penalties. THC extraction is classed as a Class A offence. I take no responsiblity for anyones actions................(as I'm not sure on the legality of posting this kind of topic).
Anyway, cannabis oil can be made using resin or weed and some growers use the leaf material that they might normally throw away. Here is what you will need:-
A pyrex dish
A 2ft length of rigid tubing with 1.5" diameter width.
Coffee filters
Cellotape
A deoderant can lid (1.8" diameter)
2 x 200ml of butane lighter gas
A grinder of some description
1oz. of leaf/normal weed
Step 1
Grind up the leaf/weed as fine as you can. The finer the weed, the more oil is produced.
Step 2
Rip the coffee filter open and tape it to one end of the tubing, making sure that it is attached firmly and that there are no gaps.
Step 3
Slowly and carefully, empty all of the weed into the tube.
Step 4
Attach the deoderant lid (or equivelant) to the open end of the tube and seal it air tight with tape. Make a small hole in the top of the lid.
Step 5
Lighter gas usually comes with lighter attachments in the lid. Remove the one with the biggest hole at the end and fit that into the hole in the deoderant lid, making sure its a tight fit and air tight.
Step 6
Now, you're ready to go! Place the pyrex dish on the floor and holding the tube (filter end down) over the pyrex dish empty one can of gas into the top end of the tube.
Step 7
Not much will happen yet so immediately empty the 2nd can into the tube and keep an eye on the dish. A liquid will start to hiss and gush out the bottom into the dish. Keep clear of the fumes, you don't want a headache! the gas will quickly evaporate and the liquid will become a honey yellow colour. Once all the liquid has evaporated, you will be left with cannabis honey oil. Scape this off the dish and store it in a homemade plastic wrap.
Step 8
Skin up and get absolutely mashed :D ..................
Anyway, cannabis oil can be made using resin or weed and some growers use the leaf material that they might normally throw away. Here is what you will need:-
A pyrex dish
A 2ft length of rigid tubing with 1.5" diameter width.
Coffee filters
Cellotape
A deoderant can lid (1.8" diameter)
2 x 200ml of butane lighter gas
A grinder of some description
1oz. of leaf/normal weed
Step 1
Grind up the leaf/weed as fine as you can. The finer the weed, the more oil is produced.
Step 2
Rip the coffee filter open and tape it to one end of the tubing, making sure that it is attached firmly and that there are no gaps.
Step 3
Slowly and carefully, empty all of the weed into the tube.
Step 4
Attach the deoderant lid (or equivelant) to the open end of the tube and seal it air tight with tape. Make a small hole in the top of the lid.
Step 5
Lighter gas usually comes with lighter attachments in the lid. Remove the one with the biggest hole at the end and fit that into the hole in the deoderant lid, making sure its a tight fit and air tight.
Step 6
Now, you're ready to go! Place the pyrex dish on the floor and holding the tube (filter end down) over the pyrex dish empty one can of gas into the top end of the tube.
Step 7
Not much will happen yet so immediately empty the 2nd can into the tube and keep an eye on the dish. A liquid will start to hiss and gush out the bottom into the dish. Keep clear of the fumes, you don't want a headache! the gas will quickly evaporate and the liquid will become a honey yellow colour. Once all the liquid has evaporated, you will be left with cannabis honey oil. Scape this off the dish and store it in a homemade plastic wrap.
Step 8
Skin up and get absolutely mashed :D ..................